Heinekev
Worked great for methe driver is good

nofy
Works with Windows XP Professional

kitsana
Despues de mucho busca busca parece que este funciona de todas formas GRACIAS

Piechta
The driver works properly

Ngnikos
thanks a lot It works perfect with Win98.

welfor
Working Well

Harald
oi estou meio perdido no site mas o mesmo e shows

Evengard
Download and extract to folder.

Sesshoumaru - sama
Install very good

download
this is a great site for drivers. i wish i could save them to floppy easier

Dr.Z
MUITO BOM MESMO

Mayky
Thank you all this is the one I needed and it works AWESOME I really appreciate it

Deliciosoavatard
To get the latest 4.51PG Bios. Go to tw.gigabyte.comMotherboardSupportBIOSBIOSList.htmFind under Others GA5AX REV5.2 Download F4 2001823 Run the bios5axf4.exe file and extract the content into your harddisk. Copy the content to your bootable floppy. Bios F4 is For PCB 3.0 4.1 and 5.x. Support AMD K63 CPU. Supports 64G HDD NOTE Most of the 4.51PG Drivers posted in DriverGuide all failed to flash BIOS. A let down and a waste of time. Go direct to your mboard manufacturer site if possible.Flashing bios is simple. You need to have a system formated floppy. Please note Driverguide remove all colon and http typed here thus unable to show the exact command eg format A drive or the full URL path To create a bootable floppy. you can do a command in Win98 Dos Prompt format A s or you can issue a sys a if the floppy is already formatted. Copy your downloaded bios files to your bootable floppy. Insert floppy and reboot your PC. Make sure your BIOS is set to boot off 1st from Floppy. Once booted up from floppy it will run an autoexec.bat which will execute the Awdflash bios process automatically for you. You only have to answer yes or no and that it. Hope this help. WHAT IS IN THE DOWNLOADED ZIPPED EXE FILEThere are 3 files once you installed into a temp folder. AWDFLASH.EXE autoexec.bat and 5AX.F4Copy these 3 files into a dos formatted floppy. Make sure it is bootable. See above for instruction.The autoexec batch shown below.awdflash 5AX.F4upon bootup from your bootable floppy autoexec will run awdflash automatically and will prompt you everything after that. When prompted to save your original bios just key in a name eg Origbios.bin. When prompted you whether to program your bios. click Yes and once programmed successfully. You can Press F1 to reset or F10 to exist. Remove your floppy. F1 to RESET your pc.Upon bootup your bios shows F4 instead which initially it was 1.4. Press Del to check your Bios configuration do not reset to default. The new F4 bios for 4.51PG will be able to detect your higher capacity harddisk and auto config it. MBOARD BIOS Different modelstw.gigabyte.comMotherboardSupportBIOSBIOSList.htm

maxim__
YES thank you for including the FCC ID FCC REG number from the modem so I can be sure that this is for my modem

[Across]Light
What can i do with this Drivers

DjMilk
Ufa.. me salvaron no saben cuanto lo necesitaba vale

pekoso
i downloaded it ....and the setup asked for disk 4 and there were only 3

mpapouts
is very good

chaostheoric
Thank

hankie112
I'm glad to find this driver. I plan to try it with a 7050C printer but I too need some guidance in the installation of this driver. Any help is appreciated.

derzis
IT WORKS FINE

Ely
I have a compaq computer with this cdrw and compaq has write it's a 16x but here is a 24x that's funny thx for the driver

Xniver
Imi pare rau ca nu ma descurc pre bine cu limba engleza pentru a putea citi mai multi mesajul meu dar totusi sa stiti ca sunt foarte multumit de acest driver pe care il caut de mult timp atat de bun1Q Dan